Four years isn't much time for an engine to hang around in production, but the legacy of the 351 Cleveland has been felt throughout hot rodding and motorsports in the nearly four decades since the last one was produced stateside. The 335-series engine family that the 351C belongs to technically served in the Ford engine lineup from 1970 to 1985, but the most famous and highest performance version, the 351 Cleveland, was only available in the United States from 1970 to 1974. The Aussies held onto their derivatives (the 351 and 302C) until the 1980s, but in the United States Ford evolved the Cleveland into the related but more utilitarian 351M and 400 while continuing to refine the Windsor platform.

So what was it about the 351C that was so special? Nicknamed "Cleveland" after the Cleveland, Ohio, engine plant in which most of the engines were manufactured, the Cleveland had free-breathing, canted-valve cylinder heads. Offered in two versions, the 2V version featured small-port cylinder heads with open-style combustion chambers, 2.04 intake/1.68 exhaust valves (larger than the ones used on the 390 and 428FE big-blocks), and round intake and exhaust ports. Over 90 percent of 351Cs produced were 2V. The 4V, on the other hand, had massive 2.5x1.75-inch intake ports that you could just about get your whole hand into. The valves for 4V engines built through 1972 were equally ginormous at 2.19-inch intake and 1.71-inch exhaust. The only other Ford engine with valves that large was the 460 Police Interceptor big-block. Those huge ports and valves were intended for supporting high-revving horsepower (above 3,500 rpm), but when combined with lower compression, smaller cams, and lower operating speeds on the road the big heads created a noticeable drop in torque production.

Drag and oval-track Ford racers, however, loved them. When streetability and low-rpm power was not a concern, the behemoth 4V heads supported big power with ease. Matter of fact, various Cleveland-styled heads atop Windsor-derived blocks was the powerplant of choice that powered Ford's NASCAR program up until the introduction of the clean-slate FR9 engine in 2009.

What hot rodders on the street really needed was a hybrid version of the Cleveland that combined the torque of the 2V heads and the high-rpm rush of the 4V head design. Ford of Australia had such a beast, but it never managed to make it to our shores, and getting your hands on a pair is not cheap or easy. In the ensuring years a few attempts to develop such a head have been made, each showing the big power potential in a properly balanced Cleveland head. Taking note of what worked well, what didn't, and what could be improved, Trick Flow Specialties' engineers took the best qualities of the original factory heads, added a healthy dose of hot rodder ingenuity, and created the PowerPort Cleveland 190 and 225 cylinder heads. These are the heads every Cleveland-powered muscle car has been waiting for.

Cleveland heads will bolt right onto a Windsor block, and there's certainly no debating the inherent strength and oiling benefits of the much more modern Windsor over the Cleveland, which is why every other article you're going to see on these heads will be a Clevor hybrid. We still believe in the good ol' C block though, so we're going to address the weak links and build a true Cleveland that will drop right into any original C-powered car or truck.

We're doing this build as a two-parter with Ford Performance Solutions (FPS) in Anaheim, California, sourcing most of the critical components from Trick Flow and Summit Racing. You'll have to wait until the April issue to see up close the beauty that is the Trick Flow Cleveland head, but for now we'll show you what we have in store for the bottom end that'll be pumping all that air through them.

BY THE NUMBERS
Type: 408ci Cleveland (4.030 x 4.00)
Block: stock Cleveland
Crank: Scat stroker kit form Summit Racing 1-46265BE
Rods: Scat 6.200 H-beam
Pistons: Scat forged aluminum
Rings: Scat file-fit
Bearings: MAHLE Clevite 77 from Summit Racing
Timing set: COMP Cams double roller
Bolts/studs: ARP
Cam: COMP Cams solid roller, .612/.612 lift, 245/245 duration at .050, 110 LSA

SOURCE
Trick Flow Specialties
1248 Southeast Avenue
Tallmadge
OH  44278
330-630-1555
http://www.trickflow.com
Ford Performance Solutions
714-870-7935
http://www.F-P-S.com
Comp Cams
3406 Democrat Road
Memphis
TN  38118
800-999-0853
http://www.compcams.com
Scat Enterprises
3-10/-370-5501
http://www.scatenterprises.com
Summit Racing
Akron
OH
800-230-3030
330-630-0240
http://www.summitracing.com/
ARP
800-826-3045
http://www.arp-bolts.com
  • «
  • |
  • 1
  • |
  • 2
  • |
  • View Full Article